caulk
caulk application
tip: for best results, thoroughly clean the area that will be receiving the caulk. pick up the caulk and pull on the cap until you see a small hole. with your dominant hand, firmly grip the caulk around the base of the dispenser. position the caulk’s dispensing hole at an angle against the crack that needs to be filled. be sure to press the tip firmly against the crack. squeeze gently but with an even pressure, moving the caulk along the crack beginning at the bottom. after the caulk has sufficiently filled the crack, smooth by gently running a wet finger along the caulk. allow to dry two hours before applying oil or latex. for more tips on everyday household repairs go to youcandoit-wecanhelp.com |
thanks? :)
|
round here caulk rhymes with sock. :D
|
:blink:
|
:rofl: I loved that!
|
OMG....I need to spend more time at Home Depot. :rofl:
|
Quote:
Takes osuche to the wood aisle. ;) |
Too funny Wyndhy :rofl:
|
A good read... lol.
TY wyndhy. ;) |
I really need some caulk
|
I love CAULK! :lurv:
|
yeah, me too. i was using alot of caulk yesterday and learned a few things. btw, i should have mentioned to you that when the caulk is ready for the latex or oil it will be firm but flexible. and be prepared for clean up. caulk gets everywhere! i had that sticky white stuff on my shirt, my legs, my arms. it even got in my hair. and my hands were totally covered in caulk. i had to use three towels to clean it all up and then take a shower.
|
Yeah...good caulk can be pretty messy. Sounds like you had your hands full. :D
|
i did! and there's still more to come. i'm going to have to use a lot of caulk in the bedroom soon. many a crack in there, lemme tell ya! they're begging for some caulk.
it's funny how nailing hard wood against a wall will leave so many cracks needing caulk. |
I've heard that sometimes a crack just needs a good screw to go with the caulk.
|
exactly, aqua! and make sure you screw it good and hard against the wall. you may just have to screw more than once. if you can, find a stud before screwing.
|
:confused:
You're not using caulk on your trim, are you? |
no, wi. i'm using caulk on cracks.
|
Quote:
Thank goodness! I'd hate to see your trim after it has caulk smeared all over it! Not really...actually I'd like that. :slurp: |
oh! well. the caulk does get on the trim. ooey-gooey gobs of it everywhere. that's where the wet finger i mentioned comes in. i agree, it is a sight to see.
|
and now that i think on it, wildi ~'because your question is important to me~ i recommend filling any holes in trim with a good wood filler. i find they fill the hole much better. a tighter fit, if you will. perhaps wood fillers expand after they are pushed in the hole.
|
Very true wyndhy... fill in your cracks with caulk. But trim needs a good nailing, I mean really pounded good. Right after is when you want to get some good wood filler in there as well. Some people would go as far as to put a gloss coat over the trim.
|
good advice aqua. i'd add that if the wood is especially hard, screwing it against the wall would help. of couse that leaves a larger hole to be filled, but i believe wood filler would work well for that, too.
|
And if possible, nailing it from the front while screwing it from behind would probably do the trick as well.
|
that, i think, would be overkill. you might end up splintering more delicate wood.
unless we are talking about body parts. then you might be onto something, aqua. of course, we aren't talking body parts here, just hardware and technique. |
Quote:
gotta be real careful when doing that...the ends might come out the other sides! |
Quote:
:yikes: |
Hardware is my life.
|
Quote:
And what technique do you employ with your hardware? |
typically I am really into knobs
|
<<<----- has been called a knob plenty of times! :D
|
get back on topic! ^^^ :spank:
knobs! very nice touch on any repository, lil. especially ash, a nice and heavy, hard, strong and stiff wood. excellent bending qualities. don't forget pre-drilling a hole is necessary before you can screw the knob. |
oops...sorry wyndhy! :(
/me quickly diverts people's temporarily misguided attention to his pre-drilled knob I've found that it's not the size of the screw that makes a knob effective, but the quality of the knob itself. My advice to anyone out there shopping around for knobs is to get the best one you can afford. I've yet to hear of anyone that's regretted that choice, whereas I've experienced firsthand the disappointment of having to abandon a cheap knob for what should've been acquired originally. |
Yes, surely you want to a knob that you can grip firmly since it needs to endure a lot of tugging. Some people like to have knobs that are purely for decoration but I feel if you're going to take the time to screw it in, you should get as much use out of it as you can. Knobs can can if various widths, lengths, and styles so you should try out several different ones to see which will fit with your trim the best.
|
Quote:
Excellent, excellent point!!!!! You know how those things go...if someone sees a knob, they're gonna pull it! It's human nature! Thank you for pointing that out! |
true, true. don't think you have to go out and get the biggest knob you can find. i would even suggest buying plain wood knobs and enhancing them yourself. after careful manual work, like applying some latex, the knob will ususally look bigger.
|
If you are really good you can add ridges or 'ribs' to the sides of the knob with careful application of the latex.
|
which would not only enhance the knob visually but really give it some tactile interest, something for your fingers to feel and explore as you pull on the knob.
nice suggestion, aqua! |
back to the pre-drilling.... I have heard and think it is an excellent idea to have two drills at the ready. Just in case the first one doesn't do the trick.
For me, knob choice is very difficult. narrowing my selection down to just one seems to be an impossible task. Why pick up just one knob when it's better to have several on hand. A varied selection will ensure that you always have the right knob for the job. |
Definitely Lil... and it's always good to have an extra tool on hand.
|
All times are GMT -5. The time now is 10:23 PM. |
Powered by: vBulletin Version 3.0.10
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.